[ Feature ] | |
---|---|
향상된 디지털 트리거링 대부분의 디지털 오실로스코프는 여전히 비교기를 기반으로 하는 아날로그 트리거 아키텍처를 사용합니다. 이로써 항상 보정할 수 없는 시간과 진폭 오류가 발생하여 대개 높은 대역폭에서 트리거 감도를 제한합니다. 1991년 PICO는 실제 디지털화된 데이터를 사용하여 디지털 트리거링의 사용을 시작했습니다. 이러한 기술은 트리거 에러를 적게해주며 아주 작은 신호들과, 높은 대역폭에도 불구하고 오실로스코프의 트리거를 가능하게 합니다. 트리거레벨과 히스테리시스는 높은 정확도와 분해능을 세팅해줍니다. 재설정 지연 감소는 디지털 트리거링과 세그먼트 메모리와 함께 새로운 파형이 매 마이크로초 버퍼가 가득 찰때까지 캡쳐할 수 있도록 합니다. PicoScope3000시리즈는 펄스폭을 포함한 업계 최고의 고급 트리거링과 윈도우, 드롭아웃을 제공합니다. 게다가 로직 트리거링을 사용하면 16개의 디지털 입력중 일부 혹은 전부 사용자 정의 패턴과 일치할때 스코프를 트리거할 수 있습니다. |
|
하드웨어 가속 엔진[HAL3] 일부 오실로스코프는 딥 메모리를 활성화할 때 어려움을 겪습니다. 화면 업데이트 속도가 느려지고 컨트롤이 응답하지 않게 됩니다. PicoScope 3000 시리즈는 오실로스코프 내부의 전용 하드웨어 가속 엔진을 사용하여 이러한 제한을 피합니다. 대규모 병렬 설계로 PC 화면에 표시할 파형 이미지를 효과적으로 생성하고 초당 4억 4천만 개 이상의 샘플을 화면에 연속 캡처 및 표시할 수 있습니다. PicoScope 오실로스코프는 PC 기반 및 벤치탑 경쟁 제품보다 딥 메모리를 더 잘 관리합니다. PicoScope 3000 시리즈에는 3세대 하드웨어 가속(HAL3)이 장착되어 있습니다. 이는 초당 100,000개 이상의 파형 업데이트 속도 및 분할 메모리/급속 트리거 모드를 허용하는 등 오실로스코프 작동 영역의 속도를 높입니다. 하드웨어 가속엔진은 병목 현상이 제거되는것을 USB 연결 혹은 PC프로세서 수행에 대한 모든 문제를 제거합니다. |
|
초당 10만 파형 지속성 모드는 동일한 보기에 여러 파형을 빠르게 중첩하여 이전 파형보다 더 밝은 색상으로 더 자주 혹은 더 새로운 파형을 그립니다. 기존 아날로그 스코프의 형광 디스플레이를 에뮬레이트하며 비디오 파형과 아날로그 변조 신호와 같은 복잡한 아날로그 신호를 표시하고 해석하는데 유용합니다. 하드웨어 가속 엔진[HAL3]는 지속성 모드에서 초당 10만의 파형 업데이트 속도를 가집니다 - 글릿치를 빨리 발견하고 지터를 관측하기위해 초당 수천가지의 파형을 수집합니다. |
|
파형 버퍼와 네비게이터 파형에서 글리치를 발견했지만 스코프를 중지할때가지 글리치가 사라졌습니까? PicoScope라면 글리치를 놓치거나 다른 과도현상을 걱정할 필요가 없습니다. PicoScope는 원형 파형 버퍼에 마지막 만개의 오실로스코프 혹은 스펙트럼 파형을 저장할 수 있습니다. 버퍼 네비게이터는 네비게이팅과 파형 검색의 효과를 제공하며, 효과적으로 시간을 되돌릴 수 있습니다. 마스크 제한 테스트 같은 툴로 버퍼의 각 파형을 스캔하여 마스크 위반을 찾을 수 있습니다 |
|
마스크 제한 테스트 마스크 제한 테스트를 통해 라이브 신호를 양호한 신호와 비교할 수 있으며 프로덕션과 디버깅 환경을 위해 설계되었습니다. 간단히 양호한 신호를 캡쳐하고, 마스크를 주변에 그리고, 그런 다음 테스트 중인 시스템에 연결합니다. PicoScope는 마스크 위반을 체크하고 성공/실패 테스트를 수행하고, 간헐적인 글릿치를 캡쳐하고, 측정 윈도우창에 실패 횟수와 다른 통계를 보여줍니다. |
|
Oscilloscope — vertical (analog inputs) | ||||||||
---|---|---|---|---|---|---|---|---|
PicoScope Model | 3203D & MSO |
3204D & MSO |
3205D & MSO |
3206D & MSO |
3403D & MSO |
3404D & MSO |
3405D & MSO |
3406D & MSO |
Input channels | 2 channels, BNC single-ended | 4 channels, BNC single-ended | ||||||
Bandwidth (−3 dB) |
50 MHz | 70 MHz | 100 MHz | 200 MHz | 50 MHz | 70 MHz | 100 MHz | 200 MHz |
Rise time (calculated) | 7.0 ns | 5.0 ns | 3.5 ns | 1.75 ns | 7.0 ns | 5.0 ns | 3.5 ns | 1.75 ns |
Hardware bandwidth limiter | Switchable, 20 MHz | |||||||
Vertical resolution | 8 bits | |||||||
Input ranges | ±20 mV to ±20 V full scale in 10 ranges | |||||||
Input sensitivity | 4 mV/div to 4 V/div in 10 vertical divisions | |||||||
Input coupling | AC / DC, programmable | |||||||
Input characteristics | 1 MΩ ±1%, in parallel with 14 pF ±1 pF | |||||||
DC accuracy | ±3% of full scale ±200 μV | |||||||
Analog offset range (vertical position adjust) |
±250 mV (20 mV, 50 mV, 100 mV, 200 mV ranges) ±2.5 V (500 mV, 1 V, 2 V ranges) ±20 V (5 V, 10 V, 20 V ranges) |
|||||||
Offset adjust accuracy | ±1% of offset setting, additional to DC accuracy | |||||||
Overvoltage protection | ±100 V (DC + AC peak) |
Oscilloscope — vertical (digital inputs, MSOs only) | ||||||||
---|---|---|---|---|---|---|---|---|
Input channels | 16 channels (2 ports of 8 channels each) | |||||||
Input connectors | 2.54 mm pitch, 10 x 2 way connector | |||||||
Maximum input frequency | 100 MHz (200 Mb/s) | |||||||
Minimum detectable pulse width | 5 ns | |||||||
Channel-to-channel skew | 2 ns, typical | |||||||
Minimum input slew rate | 10 V/µs | |||||||
Input impedance | 200 kΩ ±2% ∥ 8 pF ±2 pF | |||||||
Input dynamic range | ±20 V | |||||||
Overvoltage protection | ±50 V | |||||||
Digital threshold range | ±5 V | |||||||
Threshold grouping | Two independent threshold controls: D0...D7 and D8...D15 | |||||||
Threshold selection | TTL, CMOS, ECL, PECL, user-defined | |||||||
Threshold accuracy | < ±350 mV (inclusive of hysteresis) | |||||||
Hysteresis | < ±250 mV | |||||||
Minimum input voltage swing | 500 mV pk-pk |
Oscilloscope — horizontal | ||||||||
---|---|---|---|---|---|---|---|---|
PicoScope Model | 3203D & MSO |
3204D & MSO |
3205D & MSO |
3206D & MSO |
3403D & MSO |
3404D & MSO |
3405D & MSO |
3406D & MSO |
Maximum sampling rate (real-time) |
1 GS/s (1 analog channel) |
|||||||
Maximum effective sampling rate (repetitive signals)** | 2.5 GS/s | 5 GS/s | 10 GS/s | 2.5 GS/s | 5 GS/s | 10 GS/s | ||
Maximum sampling rate (continuous streaming mode) |
17 MS/s in PicoScope software 125 MS/s when using the supplied SDK (PC-dependent) |
|||||||
Maximum capture rate | 100,000 waveforms/second (PC-dependent) | |||||||
Timebase ranges | 1 ns/div to 5000 s/div | 500 ps/div to 5000 s/div | 1 ns/div to 5000 s/div | 500 ps/div to 5000 s/div | ||||
Buffer memory | 64 MS | 128 MS | 256 MS | 512 MS | 64 MS | 128 MS | 256 MS | 512 MS |
Buffer memory (streaming) | 100 MS in PicoScope software. Up to available PC memory when using supplied SDK. |
|||||||
Maximum buffer segments | 10 000 in PicoScope software | |||||||
130 000 using SDK | 250 000 using SDK | 500 000 using SDK | 1 000 000 using SDK | 130 000 using SDK | 250 000 using SDK | 500 000 using SDK | 1 000 000 using SDK | |
Timebase accuracy | ±50 ppm | ±2 ppm | ±50 ppm | ±2 ppm | ||||
Timebase drift per year | ±5 ppm | ±1 ppm | ±5 ppm | ±1 ppm | ||||
Sample jitter | 3 ps RMS typical | |||||||
ADC sampling | Simultaneous on all enabled channels |
* A digital port consists of 8 digital channels, D0–7 or D8–15
** ETS mode on channel A only
Dynamic performance (typical) | ||||||||
---|---|---|---|---|---|---|---|---|
PicoScope Model | 3203D & MSO | 3204D & MSO | 3205D & MSO | 3206D & MSO | 3403D & MSO | 3404D & MSO | 3405D & MSO | 3406D & MSO |
Crosstalk | Better than 400:1 up to full bandwidth (equal voltage ranges) | |||||||
Harmonic distortion | < −50 dB at 100 kHz full scale input | |||||||
SFDR | 52 dB typical at 100 kHz full scale input (except ±20 mV range: 44 dB) |
|||||||
Noise | 110 µV RMS | 160 µV RMS | 110 µV RMS | 160 µV RMS | ||||
(typical, on ±20 mV range) | ||||||||
Bandwidth flatness | +0.3 dB, −3 dB from DC to full bandwidth, typical |
Triggering – general | ||||||||
---|---|---|---|---|---|---|---|---|
Source | Analog channels, EXT trigger (not MSOs), digital channels (MSOs only) | |||||||
Trigger modes | None, auto, repeat, single, rapid (segmented memory) | |||||||
Maximum pre–trigger capture | Up to 100% of capture size | |||||||
Maximum post–trigger delay | Up to 4 billion samples (selectable in 1 sample steps) | |||||||
Trigger rearm time | < 0.7 µs at 1 GS/s sampling rate | |||||||
Maximum trigger rate | Up to 10,000 waveforms in a 6 ms burst at 1 GS/s sampling rate, typical |
Triggering – analog channels | ||||||||
---|---|---|---|---|---|---|---|---|
Advanced triggers | Edge, window, pulse width, window pulse width, dropout, window dropout, interval, logic, runt pulse | |||||||
Trigger types (ETS mode) | Rising edge, falling edge (Ch A only) | |||||||
Trigger sensitivity | Digital triggering provides 1 LSB accuracy up to full bandwidth of scope | |||||||
Trigger sensitivity (ETS mode) | 10 mV p-p typical (at full bandwidth) |
Triggering – EXT trigger input, not MSO models | ||||||||
---|---|---|---|---|---|---|---|---|
Connector type | Front panel BNC | |||||||
Advanced triggers | Edge, pulse width, dropout, interval, logic | |||||||
Input characteristics | 1 MΩ || 14 pF | |||||||
Bandwidth | 50 MHz | 70 MHz | 100 MHz | 200 MHz | 50 MHz | 70 MHz | 100 MHz | 200 MHz |
Threshold range | ±5 V | |||||||
Coupling | DC | |||||||
Overvoltage protection | ±100 V (DC + AC peak) |
Triggering – digital channels, MSO models only | ||||||
---|---|---|---|---|---|---|
Source | D0 to D15 | |||||
Trigger types | Pattern, edge, combined pattern and edge, pulse width, dropout, interval, logic |
Function generator | ||||||||
---|---|---|---|---|---|---|---|---|
Standard output signals | Sine, square, triangle, DC voltage, ramp, sinc, Gaussian, half-sine, white noise, PRBS | |||||||
Standard signal frequency | DC to 1 MHz | |||||||
Sweep modes | Up, down, dual with selectable start / stop frequencies and increments | |||||||
Triggering | Free-run, or from 1 to 1 billion counted waveform cycles or frequency sweeps. Triggered from scope trigger or manually. | |||||||
Output frequency accuracy | As oscilloscope | |||||||
Output frequency resolution | < 0.01 Hz | |||||||
Output voltage range | ±2 V | |||||||
Output voltage adjustment | Signal amplitude and offset adjustable in approximate 1 mV steps within overall ±2 V range | |||||||
Amplitude flatness | < 0.5 dB to 1 MHz typical | |||||||
DC accuracy | ±1% of full scale | |||||||
SFDR | > 60 dB 10 kHz full scale sine wave | |||||||
Output impedance | 600 Ω | |||||||
Connector type | Front panel BNC (non-MSO models) Rear panel BNC (MSO models) |
|||||||
Overvoltage protection | ±20 V |
Arbitrary waveform generator | ||||||||
---|---|---|---|---|---|---|---|---|
Update rate | 20 MS/s | |||||||
Buffer size | 32 kS | |||||||
Resolution | 12 bits (output step size approximately 1 mV) | |||||||
Bandwidth | > 1 MHz | |||||||
Rise time (10% to 90%) | < 120 ns |
Other AWG specifications as function generator
Probe compensation output | |||
---|---|---|---|
Impedance | 600 Ω | ||
Frequency | 1 kHz | ||
Level | 2 V pk-pk, typical |
Spectrum analyzer | |
---|---|
Frequency range | DC to maximum bandwidth of scope |
Display modes | Magnitude, peak hold, average |
X axis | Linear or log 10 |
Y axis | Logarithmic (dbV, dBu, dBm, arbitrary) or linear (volts) |
Windowing functions | Rectangular, Gaussian, triangular, Blackman, Blackman–Harris, Hamming, Hann, flat-top |
Number of FFT points | Selectable from 128 to 1 million in powers of 2 |
Math channels | |
---|---|
General functions | −x, x+y, x−y, x*y, x/y, x^y, sqrt, exp, ln, log, abs, norm, sign, sin, cos, tan, arcsin, arccos, arctan, sinh, cosh, tanh, derivative, integral, delay |
Filter functions | Low pass, high pass, band stop, band pass |
Graphing functions | Frequency, duty cycle |
Multi-waveform functions | Min, max, average, peak |
Operands | All analog and digital input channels, reference waveforms, time, constants, pi |
Automatic measurements (analog channels only) | |
---|---|
Oscilloscope mode | AC RMS, true RMS, cycle time, DC average, duty cycle, falling rate, fall time, frequency, high pulse width, low pulse width, maximum, minimum, peak to peak, rise time, rising rate |
Spectrum mode | Frequency at peak, amplitude at peak, average amplitude at peak, total power, THD %, THD dB, THD+N, SFDR, SINAD, SNR, IMD |
Statistics | Minimum, maximum, average, standard deviation |
Serial decoding | |
---|---|
Protocols | 1-Wire, ARINC 429, CAN, CAN FD, DALI, DCC, DMX512, Ethernet (10BaseT, 100BaseTX), FlexRay, I²C, I²S, LIN, Manchester, MODBUS, PS/2, SENT, SPI, UART/RS-232, USB 1.0 |
Mask limit testing | |
---|---|
Statistics | Pass/fail, failure count, total count |
Display | |
---|---|
Interpolation | Linear or sin(x)/x |
Persistence modes | Digital color, analog intensity, fast, custom |
Miscellaneous | |||
---|---|---|---|
Output file formats | BMP, CSV, GIF, JPEG, MATLAB 4, PDF, PNG, PSDATA, PSSETTINGS, TXT | ||
Output functions | Copy to clipboard, print |
Software | ||
---|---|---|
Windows software | PicoScope for Windows PicoSDK Software development kit (SDK) Windows 7, 8 or 10 recommended (read more) |
|
macOS software | PicoScope for macOS (beta: feature list) Software development kit (SDK) OS versions: see release notes |
|
Linux software | PicoScope for Linux (beta: feature list) Software development kit (SDK) See Linux Software & Drivers for details of supported distributions |
|
Languages | Chinese (simplified), Chinese (traditional), Czech, Danish, Dutch, English, Finnish, French, German, Greek, Hungarian, Italian, Japanese, Korean, Norwegian, Polish, Portuguese, Romanian, Russian, Spanish, Swedish, Turkish |
Physical specifications | |||
---|---|---|---|
Dimensions | 190 mm x 170 mm x 40 mm (including connectors) | ||
Weight | < 0.5 kg | ||
Temperature range | Operating: 0 °C to 40 °C (15 °C to 30 °C for stated accuracy). Storage: –20 °C to 60 °C |
||
Humidity range | Operating: 5% RH to 80% RH non-condensing. Storage: 5% RH to 95% RH non-condensing |
||
Altitude range | Up to 2000 m | ||
Pollution degree | 2 |
General | |||
---|---|---|---|
Package contents | PicoScope 3000D Series oscilloscope 2 or 4 switchable 10:1/1:1 oscilloscope probes Quick Start Guide USB 3.0 cable AC power adaptor (4-channel models only) TA136 digital cable (MSOs only) 2 × TA139 pack of 10 logic test clips (MSOs only) |
||
PC connectivity | USB 3.0 SuperSpeed (USB 2.0 compatible) | ||
Power requirements | Powered from a single USB 3.0 port or two USB 2.0 ports. 4-channel models: AC adaptor included for use with USB ports that supply less than 1200 mA |
||
Safety approvals | Designed to EN 61010-1:2010 | ||
EMC approvals | Tested to EN 61326-1:2006 and FCC Part 15 Subpart B | ||
Environmental approvals | RoHS and WEEE compliant | ||
Warranty | - years |